/** @file
  EFI Storage Security Command Protocol as defined in UEFI 2.3.1 specification.
  This protocol is used to abstract mass storage devices to allow code running in
  the EFI boot services environment to send security protocol commands to mass
  storage devices without specific knowledge of the type of device or controller
  that manages the device.

  Copyright (c) 2011, Intel Corporation. All rights reserved.<BR>
  This program and the accompanying materials
  are licensed and made available under the terms and conditions of the BSD License
  which accompanies this distribution.  The full text of the license may be found at
  http://opensource.org/licenses/bsd-license.php

  THE PROGRAM IS DISTRIBUTED UNDER THE BSD LICENSE ON AN "AS IS" BASIS,
  WITHOUT WARRANTIES OR REPRESENTATIONS OF ANY KIND, EITHER EXPRESS OR IMPLIED.

**/

#ifndef __STORAGE_SECURITY_COMMAND_H__
#define __STORAGE_SECURITY_COMMAND_H__

#define EFI_STORAGE_SECURITY_COMMAND_PROTOCOL_GUID \
  { \
    0xC88B0B6D, 0x0DFC, 0x49A7, {0x9C, 0xB4, 0x49, 0x07, 0x4B, 0x4C, 0x3A, 0x78 } \
  }

typedef struct _EFI_STORAGE_SECURITY_COMMAND_PROTOCOL  EFI_STORAGE_SECURITY_COMMAND_PROTOCOL;

/**
  Send a security protocol command to a device that receives data and/or the result
  of one or more commands sent by SendData.

  The ReceiveData function sends a security protocol command to the given MediaId.
  The security protocol command sent is defined by SecurityProtocolId and contains
  the security protocol specific data SecurityProtocolSpecificData. The function
  returns the data from the security protocol command in PayloadBuffer.

  For devices supporting the SCSI command set, the security protocol command is sent
  using the SECURITY PROTOCOL IN command defined in SPC-4.

  For devices supporting the ATA command set, the security protocol command is sent
  using one of the TRUSTED RECEIVE commands defined in ATA8-ACS if PayloadBufferSize
  is non-zero.

  If the PayloadBufferSize is zero, the security protocol command is sent using the
  Trusted Non-Data command defined in ATA8-ACS.

  If PayloadBufferSize is too small to store the available data from the security
  protocol command, the function shall copy PayloadBufferSize bytes into the
  PayloadBuffer and return EFI_WARN_BUFFER_TOO_SMALL.

  If PayloadBuffer or PayloadTransferSize is NULL and PayloadBufferSize is non-zero,
  the function shall return EFI_INVALID_PARAMETER.

  If the given MediaId does not support security protocol commands, the function shall
  return EFI_UNSUPPORTED. If there is no media in the device, the function returns
  EFI_NO_MEDIA. If the MediaId is not the ID for the current media in the device,
  the function returns EFI_MEDIA_CHANGED.

  If the security protocol fails to complete within the Timeout period, the function
  shall return EFI_TIMEOUT.

  If the security protocol command completes without an error, the function shall
  return EFI_SUCCESS. If the security protocol command completes with an error, the
  function shall return EFI_DEVICE_ERROR.

  @param  This                         Indicates a pointer to the calling context.
  @param  MediaId                      ID of the medium to receive data from.
  @param  Timeout                      The timeout, in 100ns units, to use for the execution
                                       of the security protocol command. A Timeout value of 0
                                       means that this function will wait indefinitely for the
                                       security protocol command to execute. If Timeout is greater
                                       than zero, then this function will return EFI_TIMEOUT if the
                                       time required to execute the receive data command is greater than Timeout.
  @param  SecurityProtocolId           The value of the "Security Protocol" parameter of
                                       the security protocol command to be sent.
  @param  SecurityProtocolSpecificData The value of the "Security Protocol Specific" parameter
                                       of the security protocol command to be sent.
  @param  PayloadBufferSize            Size in bytes of the payload data buffer.
  @param  PayloadBuffer                A pointer to a destination buffer to store the security
                                       protocol command specific payload data for the security
                                       protocol command. The caller is responsible for having
                                       either implicit or explicit ownership of the buffer.
  @param  PayloadTransferSize          A pointer to a buffer to store the size in bytes of the
                                       data written to the payload data buffer.

  @retval EFI_SUCCESS                  The security protocol command completed successfully.
  @retval EFI_WARN_BUFFER_TOO_SMALL    The PayloadBufferSize was too small to store the available
                                       data from the device. The PayloadBuffer contains the truncated data.
  @retval EFI_UNSUPPORTED              The given MediaId does not support security protocol commands.
  @retval EFI_DEVICE_ERROR             The security protocol command completed with an error.
  @retval EFI_NO_MEDIA                 There is no media in the device.
  @retval EFI_MEDIA_CHANGED            The MediaId is not for the current media.
  @retval EFI_INVALID_PARAMETER        The PayloadBuffer or PayloadTransferSize is NULL and
                                       PayloadBufferSize is non-zero.
  @retval EFI_TIMEOUT                  A timeout occurred while waiting for the security
                                       protocol command to execute.

**/
typedef
EFI_STATUS
(EFIAPI *EFI_STORAGE_SECURITY_RECEIVE_DATA)(
  IN EFI_STORAGE_SECURITY_COMMAND_PROTOCOL    *This,
  IN UINT32                                   MediaId,
  IN UINT64                                   Timeout,
  IN UINT8                                    SecurityProtocolId,
  IN UINT16                                   SecurityProtocolSpecificData,
  IN UINTN                                    PayloadBufferSize,
  OUT VOID                                    *PayloadBuffer,
  OUT UINTN                                   *PayloadTransferSize
  );

/**
  Send a security protocol command to a device.

  The SendData function sends a security protocol command containing the payload
  PayloadBuffer to the given MediaId. The security protocol command sent is
  defined by SecurityProtocolId and contains the security protocol specific data
  SecurityProtocolSpecificData. If the underlying protocol command requires a
  specific padding for the command payload, the SendData function shall add padding
  bytes to the command payload to satisfy the padding requirements.

  For devices supporting the SCSI command set, the security protocol command is sent
  using the SECURITY PROTOCOL OUT command defined in SPC-4.

  For devices supporting the ATA command set, the security protocol command is sent
  using one of the TRUSTED SEND commands defined in ATA8-ACS if PayloadBufferSize
  is non-zero. If the PayloadBufferSize is zero, the security protocol command is
  sent using the Trusted Non-Data command defined in ATA8-ACS.

  If PayloadBuffer is NULL and PayloadBufferSize is non-zero, the function shall
  return EFI_INVALID_PARAMETER.

  If the given MediaId does not support security protocol commands, the function
  shall return EFI_UNSUPPORTED. If there is no media in the device, the function
  returns EFI_NO_MEDIA. If the MediaId is not the ID for the current media in the
  device, the function returns EFI_MEDIA_CHANGED.

  If the security protocol fails to complete within the Timeout period, the function
  shall return EFI_TIMEOUT.

  If the security protocol command completes without an error, the function shall return
  EFI_SUCCESS. If the security protocol command completes with an error, the function
  shall return EFI_DEVICE_ERROR.

  @param  This                         Indicates a pointer to the calling context.
  @param  MediaId                      ID of the medium to receive data from.
  @param  Timeout                      The timeout, in 100ns units, to use for the execution
                                       of the security protocol command. A Timeout value of 0
                                       means that this function will wait indefinitely for the
                                       security protocol command to execute. If Timeout is greater
                                       than zero, then this function will return EFI_TIMEOUT if the 
                                       time required to execute the receive data command is greater than Timeout.
  @param  SecurityProtocolId           The value of the "Security Protocol" parameter of
                                       the security protocol command to be sent.
  @param  SecurityProtocolSpecificData The value of the "Security Protocol Specific" parameter
                                       of the security protocol command to be sent.
  @param  PayloadBufferSize            Size in bytes of the payload data buffer.
  @param  PayloadBuffer                A pointer to a destination buffer to store the security
                                       protocol command specific payload data for the security
                                       protocol command.

  @retval EFI_SUCCESS                  The security protocol command completed successfully.
  @retval EFI_UNSUPPORTED              The given MediaId does not support security protocol commands.
  @retval EFI_DEVICE_ERROR             The security protocol command completed with an error.
  @retval EFI_NO_MEDIA                 There is no media in the device.
  @retval EFI_MEDIA_CHANGED            The MediaId is not for the current media.
  @retval EFI_INVALID_PARAMETER        The PayloadBuffer is NULL and PayloadBufferSize is non-zero.
  @retval EFI_TIMEOUT                  A timeout occurred while waiting for the security
                                       protocol command to execute.

**/
typedef
EFI_STATUS
(EFIAPI *EFI_STORAGE_SECURITY_SEND_DATA) (
  IN EFI_STORAGE_SECURITY_COMMAND_PROTOCOL    *This,
  IN UINT32                                   MediaId,
  IN UINT64                                   Timeout,
  IN UINT8                                    SecurityProtocolId,
  IN UINT16                                   SecurityProtocolSpecificData,
  IN UINTN                                    PayloadBufferSize,
  IN VOID                                     *PayloadBuffer
);

///
/// The EFI_STORAGE_SECURITY_COMMAND_PROTOCOL is used to send security protocol
/// commands to a mass storage device. Two types of security protocol commands
/// are supported. SendData sends a command with data to a device. ReceiveData
/// sends a command that receives data and/or the result of one or more commands
/// sent by SendData.
///
/// The security protocol command formats supported shall be based on the definition
/// of the SECURITY PROTOCOL IN and SECURITY PROTOCOL OUT commands defined in SPC-4.
/// If the device uses the SCSI command set, no translation is needed in the firmware
/// and the firmware can package the parameters into a SECURITY PROTOCOL IN or SECURITY
/// PROTOCOL OUT command and send the command to the device. If the device uses a
/// non-SCSI command set, the firmware shall map the command and data payload to the
/// corresponding command and payload format defined in the non-SCSI command set
/// (for example, TRUSTED RECEIVE and TRUSTED SEND in ATA8-ACS).
///
/// The firmware shall automatically add an EFI_STORAGE_SECURITY_COMMAND_PROTOCOL
/// for any storage devices detected during system boot that support SPC-4, ATA8-ACS
/// or their successors.
///
struct _EFI_STORAGE_SECURITY_COMMAND_PROTOCOL {
  EFI_STORAGE_SECURITY_RECEIVE_DATA ReceiveData;
  EFI_STORAGE_SECURITY_SEND_DATA    SendData;
};

extern EFI_GUID gEfiStorageSecurityCommandProtocolGuid;

#endif