/** @file
  TPM Interface Specification definition.
  It covers both TPM1.2 and TPM2.0.

Copyright (c) 2016 - 2018, Intel Corporation. All rights reserved.<BR>
SPDX-License-Identifier: BSD-2-Clause-Patent

**/

#ifndef _TPM_TIS_H_
#define _TPM_TIS_H_

//
// Set structure alignment to 1-byte
//
#pragma pack (1)

//
// Register set map as specified in TIS specification Chapter 10
//
typedef struct {
  ///
  /// Used to gain ownership for this particular port.
  ///
  UINT8                             Access;             // 0
  UINT8                             Reserved1[7];       // 1
  ///
  /// Controls interrupts.
  ///
  UINT32                            IntEnable;          // 8
  ///
  /// SIRQ vector to be used by the TPM.
  ///
  UINT8                             IntVector;          // 0ch
  UINT8                             Reserved2[3];       // 0dh
  ///
  /// What caused interrupt.
  ///
  UINT32                            IntSts;             // 10h
  ///
  /// Shows which interrupts are supported by that particular TPM.
  ///
  UINT32                            IntfCapability;     // 14h
  ///
  /// Status Register. Provides status of the TPM.
  ///
  UINT8                             Status;             // 18h
  ///
  /// Number of consecutive writes that can be done to the TPM.
  ///
  UINT16                            BurstCount;         // 19h
  UINT8                             Reserved3[9];
  ///
  /// Read or write FIFO, depending on transaction.
  ///
  UINT32                            DataFifo;           // 24h
  UINT8                             Reserved4[0xed8];   // 28h
  ///
  /// Vendor ID
  ///
  UINT16                            Vid;                // 0f00h
  ///
  /// Device ID
  ///
  UINT16                            Did;                // 0f02h
  ///
  /// Revision ID
  ///
  UINT8                             Rid;                // 0f04h
  UINT8                             Reserved[0x7b];     // 0f05h
  ///
  /// Alias to I/O legacy space.
  ///
  UINT32                            LegacyAddress1;     // 0f80h
  ///
  /// Additional 8 bits for I/O legacy space extension.
  ///
  UINT32                            LegacyAddress1Ex;   // 0f84h
  ///
  /// Alias to second I/O legacy space.
  ///
  UINT32                            LegacyAddress2;     // 0f88h
  ///
  /// Additional 8 bits for second I/O legacy space extension.
  ///
  UINT32                            LegacyAddress2Ex;   // 0f8ch
  ///
  /// Vendor-defined configuration registers.
  ///
  UINT8                             VendorDefined[0x70];// 0f90h
} TIS_PC_REGISTERS;

//
// Restore original structure alignment
//
#pragma pack ()

//
// Define pointer types used to access TIS registers on PC
//
typedef TIS_PC_REGISTERS  *TIS_PC_REGISTERS_PTR;

//
// Define bits of ACCESS and STATUS registers
//

///
/// This bit is a 1 to indicate that the other bits in this register are valid.
///
#define TIS_PC_VALID                BIT7
///
/// Indicate that this locality is active.
///
#define TIS_PC_ACC_ACTIVE           BIT5
///
/// Set to 1 to indicate that this locality had the TPM taken away while
/// this locality had the TIS_PC_ACC_ACTIVE bit set.
///
#define TIS_PC_ACC_SEIZED           BIT4
///
/// Set to 1 to indicate that TPM MUST reset the
/// TIS_PC_ACC_ACTIVE bit and remove ownership for localities less than the
/// locality that is writing this bit.
///
#define TIS_PC_ACC_SEIZE            BIT3
///
/// When this bit is 1, another locality is requesting usage of the TPM.
///
#define TIS_PC_ACC_PENDIND          BIT2
///
/// Set to 1 to indicate that this locality is requesting to use TPM.
///
#define TIS_PC_ACC_RQUUSE           BIT1
///
/// A value of 1 indicates that a T/OS has not been established on the platform
///
#define TIS_PC_ACC_ESTABLISH        BIT0

///
/// Write a 1 to this bit to notify TPM to cancel currently executing command
///
#define TIS_PC_STS_CANCEL           BIT24
///
/// This field indicates that STS_DATA and STS_EXPECT are valid
///
#define TIS_PC_STS_VALID            BIT7
///
/// When this bit is 1, TPM is in the Ready state,
/// indicating it is ready to receive a new command.
///
#define TIS_PC_STS_READY            BIT6
///
/// Write a 1 to this bit to cause the TPM to execute that command.
///
#define TIS_PC_STS_GO               BIT5
///
/// This bit indicates that the TPM has data available as a response.
///
#define TIS_PC_STS_DATA             BIT4
///
/// The TPM sets this bit to a value of 1 when it expects another byte of data for a command.
///
#define TIS_PC_STS_EXPECT           BIT3
///
/// Indicates that the TPM has completed all self-test actions following a TPM_ContinueSelfTest command.
///
#define TIS_PC_STS_SELFTEST_DONE    BIT2
///
/// Writes a 1 to this bit to force the TPM to re-send the response.
///
#define TIS_PC_STS_RETRY            BIT1

//
// Default TimeOut value
//
#define TIS_TIMEOUT_A               (750  * 1000)  // 750ms
#define TIS_TIMEOUT_B               (2000 * 1000)  // 2s
#define TIS_TIMEOUT_C               (750  * 1000)  // 750ms
#define TIS_TIMEOUT_D               (750  * 1000)  // 750ms

#endif